Wather PP Manurhin. Made in France,1962. Semi-auto, double action pistol. Caliber:7.65mm(32ACP).8rds magazine. This pistol has been delivered directly from Manurhin to the Bundesministerium fuer Justiz in Wien (Ministry of Justice in Vienna, Austria) on July 13, 1962. ##################### ########## ############ Walther PP pistols were among the most important developments of the inter-war period. Produced between 1929 and 1945 in significant numbers, these pistols, among with the basically similar but smaller PPK, were widely used as police and military guns in Hitler’s Germany. After the war, production of the PP and PPK pistols was resumed in France by Manurhin under German licence. Later on, production was returned to the re-established Walther factory in the city of Ulm ab Donau (pre-war Walther factory was located in the city of Zella-Mehlis), and these pistols have seen widespread use by civilians and police, as well as for personal defense by many non-infantry officers in several European armies. Very close copies of the Walther PP were manufactured after the war by East Germany, Hungary, Romania, Turkey and USA. At the present time, Walther PP, PPK/S and PPK pistols are manufactured in the USA by the Smith & Wesson Company under licence from Walther. Walther PPK pistols are essentially similar to the larger PP pistols, except for the different design of the grip frame – while on PP pistols the grip backstrap is integral to the frame and grip panels are two separate items (left and right), on PPK pistols grip frame has a rectangular shape of a magazine channel and the backstrap is formed by the single-piece U-shaped grip unit, also usually made of plastic. While most PPK pistols were made with steel frames, in the post-war period Walther also produced some aluminum-framed PPK/L (Lightweight) pistols. Also, there are Walther PPK/S pistols, which are a cross-breed between PP and PPK, combining the PP frame with shorter PPK-style barrel and slide. These pistols were designed to avoid limitations imposed by the American Firearms Owners Protection Act of 1968. This act, in particular, limited the minimum size of a “sporting purpose” pistols that are allowed to be imported in USA, and use of the larger grip frame allowed importing these pistols instead of smaller PPK pistols, banned from importation under this law. The Walther PP is blowback-operated pistol with a fixed barrel, usually of all-steel construction. A few aluminum-framed PP pistols were built in Germany before the war, and stainless steel versions are manufactured in the USA under Walther’s licence since the mid-1980s. The trigger is double-action, with an exposed hammer and a frame-mounted manual safety/decocker; the lockwork is somewhat complicated in a typical German manner and has many small parts and pins. Sights are fixed, with the rear sight blade dovetailed into the slide. Magazines are single-stack; the magazine release button is usually located at the left side of the frame, just below the slide and in front of the grip panel. However, at least some PP pistols were made both before and after the war with so called “European-style” magazine release, located at the heel of the grip. Walther PP and PPK pistols are fitted with a loaded chamber indicator, made in the form of a small pin that protrudes from the rear of the slide (above the hammer) when a cartridge is in the chamber. This indicator is not present on .22LR models. It must be noted that most of PP and PPK pistols were made in 7,65mm (.32ACP) caliber, with 9mm Kurz (9x17, .380ACP) running distant second. The .22LR version was made in some numbers, and so far most rare is the 6,35mm / .25ACP version, with very few guns made early in production history of both pistols. How to field-strip (disassemble) Walther PP or PPK: 1) remove the magazine by pressing the magazine release button; 2) check that the chamber is empty; 3) pull the trigger-guard downwards, then swing it to one side to lock in the open position; 4) pull the slide all the way back, then raise the rear of the slide to the top, and off the frame rails; 5) carefully ease the slide forward and off the barrel; 6) remove the return spring from the barrel. Reassemble in reverse order. ######################## ############ ############# Manurhin PP (Walther PP type) french Pistol Thanks to Kyrie Ellis / Moderator - Cruffler_Forum on Yahoo Groups for his contribution for this page ... A bit of history may be in order here.... Immediately following World War Two Carl Walther escaped from what would soon become East Germany (the Walther factory at Zell-Mehlis was located in the Soviet Zone of occupied Germany) to what would soon be West Germany with little more than the clothes on his back - and the patents for his firearms. With post-war West Germany forbidden the manufacture of firearms, Walther was essentially out of business and earned his living by working as a mechanic. In 1952 Walther entered into an agreement with Manurhin that permitted Manurhin to produce his model PP and PPK pistols in France, under a royalty agreement. These royalty payments, and the changing political scene, allowed Walther to rebuild his own manufacturing plant in Ulm, Germany, and begin production of his Model P.38 pistol there. Walther's close relationship with Manurhin continued to 1986, and all post-war Walther model PP and PPK pistols produced prior to 1986 were actually produced at the Manurhin plant, regardless of whether the pistols are marked "Manurhin" or "Walther" and proofed at St. Etienne or Ulm. &&&&&&&&&&&&&&&&&&&&&&&&&&&& BTW: in April of 1945 Comrade Hitler had himself shot with Walther PP.